Powermatic 1791291K Manuel d'utilisateur

Operating Instructions and Parts Manual Combination Belt/Disc Sander Model 31A WALTER MEIER (Manufacturing) Inc. 427 New Sanford Road LaVergne

10Assembly Tools required: wrenches – 10, 13 and 17mm hex (Allen) wrench – 8mm Cross-point screwdriver Installing Sander on Stand Refer to Figure 5:

11Installing and Tracking Abrasive Belt To install the abrasive belt, proceed as follows Refer to Figures 7 and 8: 1. Loosen the knob (A) and swing

122. Insert the two M10x25 socket head cap screws (AA), with two M10 flat washers (EE), through the fence base and into the threaded holes on the pi

13Dust Outlet and Cord Plate Refer to Figure 12: 1. Install the dust outlet using the four M6 x 12 pan head flanged screws (FF). 2. Single Phase mod

14Converting from 230 Volt to 460 Volt (Three Phase Only) Consult the wiring diagram inside the starter box cover. A similar diagram is also included

15Adjustments Before putting power to the sander, inspect the machine thoroughly. Check to ensure that all screws are tight, all mechanical functions

16 A zero-degree stop screw (D, Figure 17) is located behind the disc. The block should be set for quick placement of the table to the zero position

17Operation The belt and disc sander can be equipped with a variety of abrasives and grit sizes to handle a wide variety of materials, from soft wood

18The chart on page 20 lists the various grits and materials used and lists the grit symbols. It is generally better to start with a slightly coarser

19Maintenance Before doing maintenance on the sander, disconnect it from the electrical supply by pulling out the plug or switching off the main sw

2 Warranty and Service Walter Meier (Manufacturing) Inc., warrants every product it sells. If one of our tools needs service or repair, one of our Au

20Guide to Sanding Belts and Discs

21Troubleshooting Trouble Probable Cause Remedy Sander will not start. Disconnected from power source. Check connection to source. Incorrect volta

22Parts List: 31A Stand Assembly (1PH) Index No. Part No. Description Size Qty 1 ... 31A-78 ...Stand ...

2331A Stand Assembly (1PH)

24Parts List: 31A Stand Assembly (3PH) Index No. Part No. Description Size Qty 1 ... 31A-78-3 ...Stand (3P H) ...

2531A Stand Assembly (3PH)

26Parts List: 31A Sander Body Assembly Index No. Part No. Description Size Qty 1 ... 31A-1 ...Cast Base ...

2758 ... 31A-52 ...Lock Washer ...M16 ... 2 59 ..

2831A Sander Body Assembly

29Electrical Connections (1 Phase)

3 Table of Contents Warranty and Service...

30Electrical Connections (3 Phase) 95RMa nAut o969798OR14NOA2174T2 6T32T113 NO5L33L 2A11L 195RMa nAut o969798OR14NOA2174T2 6T32T113NO5L33L 2A11L 1

31

32 WALTER MEIER (Manufacturing) Inc. 427 New Sanford Road LaVergne, Tennessee 37086 Phone: 800-274-6848 www.powermat

4 Warning As with all machines, there is a certain amount of hazard involved with the use of this sander. Use the machine with the respect and cauti

5 Hand safety. Keep fingers and hands away from the belt or disc. DO NOT clear sawdust from the table with the hands; use a brush. On small or thi

6 Introduction This manual is provided by Walter Meier (Manufacturing) Inc., covering the safe operation and maintenance procedures for a Powermatic

7 Grounding Instructions 1. All grounded, cord-connected tools: In the event of a malfunction or breakdown, grounding provides a path of least res

8 Dimensions Figure 2 On-Off Switch Padlock The single-phase model of the 31A Sander is equipped with a push-button switch that will accept a safe

9 Unpacking Open shipping container and check for shipping damage. Report any damage immediately to your distributor and shipping agent. Do not disc