Powermatic Single End Dovetailer DT45 Manuel d'utilisateur

Operating Instructions and Parts Manual Single End Dovetailer Model DT45 WMH TOOL GROUP, Inc. 2420 Vantage Drive Elgin, Illinois 60124 Part

103. Tighten the four socket head cap screws. Installing Switch 1. Remove any protective wrapping from the switch. 2. Remove the two socket head c

11Grounding Instructions Electrical connections must be made by a qualified electrician in compliance with all relevant codes. This machine must be

12 The temporary adapter should only be used until a properly grounded outlet can be installed by a qualified electrician. This adapter is not applic

13Adjustments Disconnect machine from power source before making adjustments. Failure to comply may cause serious injury. Lower Work Support Inside

14Template Bar The four-sided template bar, shown in Figure 16, will allow you to create “half-blind” dovetails, where the dovetails are visible on o

15 3. Continue to check the spacing by sliding the headstock across, until the dovetail cuts will be distributed evenly across the width of the work

16Buffer Pads The polyethylene buffer pads (shown in Figure 20) have slots through which they are secured to the fences by screws. These buffer pads

17Thickness of Tenon Cut To adjust the thickness of the tenon (male) cuts, you will change the depth of the tracer pin (Figure 22). 1. Disconnect m

18Drive Belt Tension The tightness of the belt that drives the spindle has been adjusted at the factory. Further adjustment may be necessary after th

19IMPORTANT: Make sure the workpiece has been cut square before making dovetails. An out-of-square workpiece will result in poor dovetail joints. 1.

2Warranty and Service WMH Tool Group, Inc., warrants every product it sells. If one of our tools needs service or repair, one of our Authorized Servi

2010. Insert the LEFT SIDE piece and clamp it in vertical position on the lower work support and against the fence. (NOTE: The bottom grooves on both

213. Plywood has a tendency to chip out on exposed edges. A back-up board should be used as needed (see Figure 29). Maintenance Before doing main

22Troubleshooting the DT45 Trouble Probable Cause Remedy Machine not plugged in. Verify machine is connected to power. Fuse blown, or circuit breake

23Trouble Probable Cause Remedy Machine will not start/restart or repeatedly trips circuit breakers or blows fuses. (continued) On/off switch failur

24Parts List: Base Assembly Index No. Part No. Description Size Qty 1... DT45-101...Worktable...

25Base Assembly

26Parts List: Headstock Assembly Index No. Part No. Description Size Qty 1... DT45-201...Spindle Assembly (Index #2 thr

27Headstock Assembly

28Parts List: Cabinet Assembly Index No. Part No. Description Size Qty 1... DT45-301...Cabinet...

29Electrical Connections – 115 volt

3Table of Contents Warranty and Service ...

30Electrical Connections – 230 volt

31

32 WMH Tool Group, Inc. 2420 Vantage Drive Elgin, Illinois 60124 Phone: 800-274-6848 www.wmhtoo

4 Warning 1. Read and understand the entire owner’s manual before attempting assembly or operation. 2. Read and understand the warnings posted on t

5 21. Give your work undivided attention. Looking around, carrying on a conversation and “horse-play” are careless acts that can result in serious i

6Introduction This manual is provided by WMH Tool Group, Inc., covering the safe operation and maintenance procedures for a Model DT45 Single End Dov

7Features of the DT45 Dovetailer Terminology Below are the terms used in this manual to identify types of cuts and measurements.

8Unpacking Open shipping container and check for shipping damage. Report any damage immediately to your distributor and shipping agent. Do not discar

9Installation & Assembly Tools required for assembly forklift or hoist with straps/slings 11mm wrench (provided) [NOTE: A socket set with ratch